Feel free to try the default Template, but keep in mind that some of the mappings may not be to your personal taste. A Template is a complete set of MIDI assignments for an NI controller. If it’s your first time with the CONTROLLER EDITOR, the default Template for your controller will load otherwise, all of your Templates will load. For this reason, we advise not to open the CONTROLLER EDITOR in a live setting. At this point, all connected Native Instruments controllers will automatically enter MIDI Mode – useful in the studio, but potential hugely confusing on the stage. You can also configure other behaviour, such as the colors used by the RGB-backlit Pads. It will let you define – or ‘assign’ – the MIDI messages sent by each control element (pads, buttons, knobs, encoders, etc), for example, Pad 13 sends note A-1, Knob 4 sends MIDI CC 2, and so on. Here’s an example of a MASCHINE mapping for TRAKTOR, with each control labelled inside CONTROLLER EDITOR.ĬONTROLLER EDITOR is basically the middleman between your MASCHINE controller and TRAKTOR – or indeed, any other combination of NI controllers and software in your studio or live setup. Alternatively, you can plan the mapping directly inside the Native Instruments CONTROLLER EDITOR application (installed with any NI controller, or downloadable here). One of the best approaches is to simply draw out a labelled diagram of the mapping with paper and pencil. There’s nothing worse than getting deep into it, then realising you didn’t leave space for some vital function. To get an idea of what mappings can do in the hands of a master, check out /midi-maps/īefore diving headlong into the MIDI mapping process, it’s crucial to plan it out. With the MASCHINE and TRAKTOR software synced, and your MASCHINE controller talking to both of them, you can begin making a MASCHINE mapping for TRAKTOR.Ī typical mapping might have an effects section, browsing controls for browsing playlists and loading tracks, Hotcues, Loop controls, Play, Sync, Tempo Bend, Flux Mode, BeatJump, and then perhaps a few of the programmer’s own secret weapons. The same key combination will switch you back into Application Mode. Shift + Control (MASCHINE MK2 & MASCHINE MK1).Shift + Channel (MASCHINE MK3 & MASCHINE STUDIO).To start, make sure your MASCHINE is in MIDI Mode. This gives you a whole new layer of assignable buttons, knobs and faders that you can program to control virtually anything inside TRAKTOR – called a mapping. However, MASCHINE – as with most Native Instruments controllers – has what’s called a MIDI Mode. In normal use, when controlling MASCHINE, the controller is in what’s known as Application Mode. However, Ableton Link is still a work in progress, and the timing tends to drift in tempo sync mode, so we recommend the old-school method of sending a virtual MIDI clock from TRAKTOR to MASCHINE. With Ableton Link, you can synchronize MASCHINE to TRAKTOR with one push of a button in each program. Obviously, if you want to actually do this during a set, then you’ll want to synchronise playback timing of the two applications. One of the beauties of the MASCHINE hardware is that it can be used to control both the MASCHINE and TRAKTOR software simultaneously. This tutorial refers to the MASCHINE MK3 hardware throughout, as that’s the device we are using, but the same techniques are applicable to all MASCHINE models. In this in-depth tutorial, you’ll learn how to do all of this and more, creating a custom TRAKTOR mapping for MASCHINE from scratch. And how about mapping MASCHINE’s multicolored pads to show which TRAKTOR features are active at a glance? Use Modifiers and Pages to create layers of controls, massively multiplying what your MASCHINE setup is capable of. You can map multiple features to one control to turbocharge your on-stage workflow and creativity. Almost any feature in TRAKTOR can be mapped, meaning that it can be controlled with MASCHINE’s pads and buttons. With the MK3 model featuring 16 RGB-backlit pads, 8 knobs with visual readout, a tactile encoder, buttons aplenty, and multiple pages of controls, there’s enough mappability here to handle all the Hotcues you can throw it at – and then some.īut back to that mapping functionality. Ever wanted to go beyond the tried-and-true “decks and mixers” control paradigm? Through the magic of mapping, anything with a MIDI output can become your new TRAKTOR controller, and there are few better blank canvases for this than MASCHINE.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |